Chu Sheng brand new Dongfeng Duolika dragging two wreckers   The new Dongfeng Dolika has adopted the original chassis of Dongfeng Dolika for the first time. Xigong Qing Chu Sheng production of a trailer with two clearing car chassis Dongfeng, Jianghuai, Qingling, Iveco, liberation, Austrian bell, etc., a wide range of options. In 2010, Dongfeng shares the integration of its Dongfeng light truck sub-brands into three categories: Capt, Dolika and Freka. Take high-end, mid-range and low-end products respectively. Dongfeng's original Dongfeng Xiao Bawang, Dongfeng Kangba, and Dongfeng Dolika are collectively referred to as “Dolicaâ€. Since then, Dongfeng Dolika has been known as a brand of Dongfeng mid-range light truck. The Dolika Cab was the first to pass the European crash test and was called the safest cab. The new Dongfeng Dolika is equipped with a 3800mm wheelbase, a 2.5-ton front axle, a 5-ton rear axle, and a 7.50-R16 wire tire; the engine can be selected from the Dongchao Chaoyang Diesel Engine Co., Ltd.'s Chaoyang Diesel Engine CY4102-E3C . The city can choose three diesel engines from Chaoyang CY4102-C3C. The Dongfeng Doolika Wrecker can be supported on the back, with a flat plate length of 5.6 meters and an inner width of 2.22 meters. The platform area is the largest in the 3-ton class of similar products, with a platform carrying capacity of 3 tons and a lifting capacity of 2.2 tons. The type and performance of the lifting ability are relatively strong. The new type of Dongfeng Dolika's folding-type flat-bed mechanism adopted by our company is our company's introduction of advanced and mature product technology and production technology from home and abroad. It has been verified by repeated use by users and has stable performance and strong reliability. For the lower front suspension accident car is more suitable to avoid damage to the front of the loaded vehicle. Flat surface using 22 pieces of stamping convex plate block combination, light weight, high strength, anti-slip performance, not easy to deformation, easy maintenance. In the area of ​​the loaded tire roller, anti-skid granular material is sprayed, which is beautiful and practical, and the coefficient of friction is increased. It is approximately 2 to 3 times more frictional adhesion than a normal flat plate. The lamp frame is stamped with a mold, light weight, high strength, beautiful appearance, generous, equipped with 24V 1.2 meters long yellow explosion flashing lights. Most of the wrecker manufacturers in China are made of ordinary steel plates. The use of folding flat plates is not a lot, and there is no latest design structure for flat loading surfaces. Chu Sheng Brand Dongfeng Duolika One drag two trucks Some of the major components of the hydraulic system adopt international famous brands, providing effective and reliable guarantee for the whole process of clearing the obstacles. Hydraulic components and hydraulic systems are inspected before procurement and finished products are put into warehouses. The hydraulic system adopts double filtering of inlet and outlet oils to fully ensure that the hydraulic components and the hydraulic system of the vehicle meet the performance requirements of the national calibration. The balance valve selected is a plate structure. It is directly mounted on the cylinder. Even if the external oil circuit connected to it fails, all agencies can maintain their original status without any effect. At the same time, this valve also has an overload protection function. When the set pressure is exceeded, the unloading can be overflowed in time to ensure the safety of the entire system; the unloading speed can be arbitrarily adjusted to achieve smooth unloading and no impact. The balance valves selected by other wrecker manufacturers in China are mostly tubular connections. Once the external oil circuit connected to it is in failure (the tubing suddenly breaks, cuts off, and the joints loosen, etc.), the corresponding mechanism will fail immediately. Open, etc.) The stable state of the connection between the wrecker and the faulty car was instantaneously broken and disengaged, resulting in a major accident. Chu Valvoline wind Duolika one with two flat wrecker minimum inclination angle of 8 degrees, the rated hoisting system lifts of 1.8 tons, four tons using a hydraulic winch rope 20 Mega thick, with four tie Belt, two auxiliary wheels, holding fork seat, one pair of supporting fork, one chain, 24V long explosive flashing lights, siren, using Rexroth hydraulic system, equipped with hand-washing device, and the flat plate is composed of a plurality of pressed preloading plates. Stronger carrying capacity. The color in the flat panel is blue, the spare tire should be under the hanging type, and the auxiliary wheel is hanging type . Chusheng Brand Dongfeng Duolika dragging two wreckers technical parameters Lifting system Maximum lifting mass ( kg ) 1800 Full reach maximum lifting capacity ( kg ) 1330 Rear support distance (mm) 2540 Support arm length ( mm ) 1640 Support arm extension stroke ( mm ) 1340 Support arm tilt angle ( 0 ) 7 Support arm downtilt ( 0 ) -9.5 Retract the maximum distance from the upper surface of the cross arm to the ground ( mm ) 550 platform Inner length ( mm ) 5580 Inner width ( mm ) 2220 Platform minimum tilt angle ( 0 ) 8 Platform working stroke ( mm ) 2700 Platform height above ground ( mm ) 1070 Flat mechanism maximum load capacity ( kg ) 3000 winch Quantity (only) 1 Each rated traction ( kN ) 40 Wire rope diameter ( mm ) φ 11 Wire rope length ( m ) 25 Winch diameter ( mm ) φ 110 Wireline minimum line speed ( m/min ) 5 end feed Bronze Fittings is designed according to kembla and connex type .but the quality is same as kembla bronze fittings and coneex bronze fittings,End Feed Bronze Fittings,end feed gunmetal fittings,kembla bronze fittings,connex bronze fittings End Feed Bronze Fittings,end feed gunmetal fittings,kembla bronze fittings,connex bronze fittings Taizhou Runde Company , https://www.zjpressfittings.com
October 03, 2022