Condenser Unit,Industrial Air Cool Condensers,Cooling Condensing Unit,Fn Type Air Cooled Condensers Jiangsu Libang Electromechanical Equipment Co.,Ltd , https://www.liboncold.com
However, if such a good product is not professional if it is not professional, what should we pay attention to?
Preparation before construction:
1. Ensure that the civil engineering, woodwork, paintwork and plumbing projects have been completed.
2, to ensure that the indoor temperature above 10 °C.
3. The base film coated on the wall (two passes) must be fully dried and the ratio of the base film to the water is 1:1. Please check the wall before construction to ensure that the wall is solid, dry, flat, clean, and colored. Consistent and moderate pH.
4, using glutinous rice glue, according to the specified method of deployment, in order to ensure the adhesive strength.
5, construction tools: laser line instrument, roller, short bristle brush, bucket, soft towel, brush, steel shovel, scraper, wallpaper knife.
Construction method
1. Check the model of the product before construction and do not put the products with intuitive problems on the wall.
2. Measure the length of the wall, and determine the length of the product according to the actual paste method and decorative effect.
3, the deployment of a suitable viscosity of glue, glutinous rice glue and water ratio of 1:1, stirring with an electric mixer, the viscosity of the glue can not be too low, otherwise prone to seepage phenomenon.
4. Use a roller to evenly adjust the glutinous rice gum on the wall. Pay attention to the thin coating of the viscous rubber on the sizing, and brush evenly. Liaoning province wall cloth wholesale Yin corner place can not be coated with too much glue, it is best to use a small brush on the thin layer of glue is enough, because the construction of excess glue on the wall will be brushed to the inside corner.
5, after brushing the glue, wait patiently for 5-10 minutes before performing the construction, so that the excess water in the glue evaporates part
6, with a laser line instrument positioning, to ensure the level of degree and verticality, the product began to pave from the inside corner, Liaoning wall covering wholesale open shop side, each paste about 1 meter need to use the laser line tester detection level vertical.
7, if the yin and yang corner of the line is not vertical, must be stacked in the corner of the construction of the construction, re-positioning with a laser line instrument after the construction.
8. It is recommended that all products be delayed by about 10 minutes during construction. In the case of low temperature dry weather (less than 11 degrees Celsius) in Liaoning Wall Wholesale, please increase the delay time to trim the edge, which can effectively solve the problem of slight shrinkage of the fabric.
9. After the initial paving is completed, use a short bristle brush to level the product from top to bottom and from the center to the circumference. Liaoning Liaobu wholesales out bubbles and excess glue, and trims edges with a sharp paper knife, and uses Clean wet towels promptly clean spilled glue
Precautions
1. When encountering natural material products (such as cotton, hemp, etc.), physical characteristics may occur, and slight shrinkage and popping seams may occur. Therefore, in the first construction, please test the position of the small face.
2. During the construction process, avoid the glue to get the surface of the product. When the wholesale of Liaoning wall cloth is found, the glue or dirt should be removed in time with a clean wet towel.
3, seamless wall cloth products are not suitable for construction with a scraper, apply a short bristle brush to flatten the treatment. Liaoning wall cloth wholesale because the brush is soft and the contact surface with the wall cloth is also larger than the scraper, the wall cloth is less squeezed, will greatly reduce the chance of seepage.
4, should not be vigorously scraped during construction to avoid the glue is squeezed to the surface of the wall cloth. Liaoning wall cloth wholesale for the bottom of the cloth for the wall cloth products, construction can not be forced to pull the wall cloth products, otherwise it will easily cause the wall cloth deformation, the edge of the wall cloth will appear butterfly phenomenon, causing uneven construction, wrinkling And other undesirable phenomena.
5. If there is an uneven wrinkle, you can iron it with a steam iron and avoid ironing the same position for a long time to prevent the seamless wall cloth from being hot deformed and affecting the appearance.
6. After the construction is completed, first check the overall paving effect, and then check the seams and the yin and yang angles. If there are unsmoothed air bubbles, lack of glue, and other problems, repairs should be done promptly.
Seamless wall cloth as a green environmental protection new home improvement material, with its waterproof antifouling, anti-mildew antibacterial, toughness crack resistance, and flame retardant, thermal insulation, sound-absorbing, anti-static, easy scrubbing, easy care, Easy to replace and many other advantages, more and more favored by the family of Liaoning wall covering wholesalers.
October 03, 2024